View AN7810NSP_196626.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Voltage Regulators
AN78xxNSP Series
3-pin positive output voltage regulator (1 A type)
I Overview
The AN78xxNSP series is a 3-pin fixed positive output type monolithic voltage regulator housed in surface mounting package. Stabilized fixed output voltage is obtained from unstable DC input voltage with using minimum external components. 9 types of fixed output voltage are available; 5 V, 6 V, 7 V, 8 V, 9 V, 10 V, 12 V, 15 V and 18 V. They can be used widely in power circuits with current capacity up to 1 A.
6.500.20 5.300.10 (4.35) (3.00)
Unit: mm
1.000.20
(1.80)
(2.50)
5.500.20
(5.50) 9.800.20
(0.20)
2.50
2 1 2.30 4.600.10
I Features
* Output voltage: 5 V, 6 V, 7 V, 8 V, 9 V, 10 V, 12 V, 15 V, 18 V * Built-in overcurrent limit circuit * Built-in thermal overload protection circuit * Built-in ASO (area of safe operation) protection circuit
3 0.750.10
(0.80)
0.55 -0.05 0.100.10
+0.10
SP-3SU Note) The package of this product will be changed to lead-free type (SP-3SUA). See the new package dimensions section later of this datasheet.
I Block Diagram
Pass Tr Current source
Current limitter
RSC
Starter
Voltage reference Error amp.
Thermal protection
R2 R1
1 Input CI CI 0.33 F, CO 0.1 F
2 FIN CO
3
Output
I Pin Descriptions
Pin No. 1 2 3 Input GND Output Description Input voltage pin Ground pin (FIN) Output voltage pin
SFF00011BEB
Publication date: November 2001
2.300.10
1.000.30
1
AN78xxNSP Series
I Absolute Maximum Ratings
Parameter Supply voltage Supply current Power dissipation
*2 *1
Symbol VCC ICC PD Topr Tstg
Range 35 364 -30 to +85 -55 to +150
Unit V mA mW C C
Operating ambient temperature Storage temperature
*1
Note) 1. *1: Except for the operating ambient temperature and storage temperature, all ratings are for Ta = 25C. *2: The power dissipation shown is the value for the independent IC without a heat sink at Ta = 85C. When Tj exceeds 150C (designed value), the internal circuit cuts off the output. 2. This IC is not suitable for car electronics equipment.
I Electrical Characteristics at Ta = 25C
* AN7805NSP (5 V type) The specified condition Tj = 25C means that the test should be carried out within so short a test time (within 10 ms) that the characteristic value drift due to the chip junction temperature rise can be ignored. Unless otherwise specified, VI = 10 V, IO = 500 mA, CI = 0.33 F and CO = 0.1 F Parameter Output voltage Output voltage tolerance Line regulation 1 Line regulation 2 Load regulation 1 Load regulation 2 Bias current Symbol VO1 VO2 Tj = 25C VI = 8 V to 20 V, IO = 5 mA to 1 A Tj = 25C, PD < 5 W Conditions Min 4.8 4.75 62 Typ 5 3 1 15 5.0 3.9 Max 5.2 5.25 100 50 100 50 8 1.3 0.5 Unit V V mV mV mV mV mA mA mA dB
REGIN1 VI = 7.5 V to 25 V, Tj = 25C REGIN2 VI = 8 V to 12 V, Tj = 25C REGL1 REGL2 IBias IO = 5 mA to 1.5 A, Tj = 25C IO = 250 mA to 750 mA, Tj = 25C Tj = 25C
Bias current fluctuation to input IBias(IN) VI = 7.5 V to 25 V, Tj = 25C Bias current fluctuation to load Ripple rejection ratio * Design reference data IBias(L) IO = 5 mA to 1 A, Tj = 25C RR VI = 8 V to 18 V, IO = 100 mA, f = 120 Hz
Note) The characteristics listed below are theoretical values based on the IC design and are not guaranteed.
Parameter Output noise voltage
Symbol VNO
Conditions f = 10 Hz to 100 kHz
Min
Typ 40 2 700 2.0 - 0.3 150
Max
Unit V V mA A mV/C C
Minimum input/output voltage VDIF(min) IO = 1 A, Tj = 25C difference Output short-circuit current Peak output current Output voltage temperature coefficient Thermal protection operating temperature IO(Short) IO(Peak) VI = 35 V, Tj = 25C Tj = 25C
VO / Ta IO = 5 mA, Tj = 0C to 125C Tj(TH) IO = 5 mA
2
SFF00011BEB
AN78xxNSP Series
I Electrical Characteristics at Ta = 25C (continued)
* AN7806NSP (6 V type) The specified condition Tj = 25C means that the test should be carried out within so short a test time (within 10 ms) that the characteristic value drift due to the chip junction temperature rise can be ignored. Unless otherwise specified, VI = 11 V, IO = 500 mA, CI = 0.33 F and CO = 0.1 F Parameter Output voltage Output voltage tolerance Line regulation 1 Line regulation 2 Load regulation 1 Load regulation 2 Bias current Symbol VO1 VO2 Tj = 25C VI = 9 V to 21 V, IO = 5 mA to 1 A Tj = 25C, PD < 5 W Conditions Min 5.75 5.7 59 Typ 6 5 1.5 14 4.0 3.9 Max 6.25 6.3 120 60 120 60 8 1.3 0.5 Unit V V mV mV mV mV mA mA mA dB
REGIN1 VI = 8.5 V to 25 V, Tj = 25C REGIN2 VI = 9 V to 13 V, Tj = 25C REGL1 REGL2 IBias IO = 5 mA to 1.5 A, Tj = 25C IO = 250 mA to 750 mA, Tj = 25C Tj = 25C
Bias current fluctuation to input IBias(IN) VI = 8.5 V to 25 V, Tj = 25C Bias current fluctuation to load Ripple rejection ratio * Design reference data IBias(L) IO = 5 mA to 1 A, Tj = 25C RR VI = 9 V to 19 V, IO = 100 mA, f = 120 Hz
Note) The characteristics listed below are theoretical values based on the IC design and are not guaranteed.
Parameter Output noise voltage
Symbol VNO
Conditions f = 10 Hz to 100 kHz
Min
Typ 40 2 700 2.0 - 0.4 150
Max
Unit V V mA A mV/C C
Minimum input/output voltage VDIF(min) IO = 1 A, Tj = 25C difference Output short-circuit current Peak output current Output voltage temperature coefficient Thermal protection operating temperature IO(Short) IO(Peak) VI = 35 V, Tj = 25C Tj = 25C
VO / Ta IO = 5 mA, Tj = 0C to 125C Tj(TH) IO = 5 mA
SFF00011BEB
3
AN78xxNSP Series
I Electrical Characteristics at Ta = 25C (continued)
* AN7807NSP (7 V type) The specified condition Tj = 25C means that the test should be carried out within so short a test time (within 10 ms) that the characteristic value drift due to the chip junction temperature rise can be ignored. Unless otherwise specified, VI = 12 V, IO = 500 mA, CI = 0.33 F and CO = 0.1 F Parameter Output voltage Output voltage tolerance Line regulation 1 Line regulation 2 Load regulation 1 Load regulation 2 Bias current Symbol VO1 VO2 Tj = 25C VI = 10 V to 22 V, IO = 5 mA to 1 A Tj = 25C, PD < 5 W Conditions Min 6.7 6.6 57 Typ 7 5 1.5 14 4.0 3.9 Max 7.3 7.4 140 70 140 70 8 1.0 0.5 Unit V V mV mV mV mV mA mA mA dB
REGIN1 VI = 9.5 V to 25 V, Tj = 25C REGIN2 VI = 10 V to 15 V, Tj = 25C REGL1 REGL2 IBias IO = 5 mA to 1.5 A, Tj = 25C IO = 250 mA to 750 mA, Tj = 25C Tj = 25C
Bias current fluctuation to input IBias(IN) VI = 9.5 V to 25 V, Tj = 25C Bias current fluctuation to load Ripple rejection ratio * Design reference data IBias(L) IO = 5 mA to 1 A, Tj = 25C RR VI = 10 V to 20 V, IO = 100 mA, f = 120 Hz
Note) The characteristics listed below are theoretical values based on the IC design and are not guaranteed.
Parameter Output noise voltage
Symbol VNO
Conditions f = 10 Hz to 100 kHz
Min
Typ 46 2 700 2.0 - 0.5 150
Max
Unit V V mA A mV/C C
Minimum input/output voltage VDIF(min) IO = 1 A, Tj = 25C difference Output short-circuit current Peak output current Output voltage temperature coefficient Thermal protection operating temperature IO(Short) IO(Peak) VI = 35 V, Tj = 25C Tj = 25C
VO / Ta IO = 5 mA, Tj = 0C to 125C Tj(TH) IO = 5 mA
4
SFF00011BEB
AN78xxNSP Series
I Electrical Characteristics at Ta = 25C (continued)
* AN7808NSP (8 V type) The specified condition Tj = 25C means that the test should be carried out within so short a test time (within 10 ms) that the characteristic value drift due to the chip junction temperature rise can be ignored. Unless otherwise specified, VI = 14 V, IO = 500 mA, CI = 0.33 F and CO = 0.1 F Parameter Output voltage Output voltage tolerance Line regulation 1 Line regulation 2 Load regulation 1 Load regulation 2 Bias current Symbol VO1 VO2 Tj = 25C VI = 11 V to 23 V, IO = 5 mA to 1 A Tj = 25C, PD < 5 W Conditions Min 7.7 7.6 56 Typ 8 6 2 12 4.0 3.9 Max 8.3 8.4 160 80 160 80 8 1.0 0.5 Unit V V mV mV mV mV mA mA mA dB
REGIN1 VI = 10.5 V to 25 V, Tj = 25C REGIN2 VI = 11 V to 17 V, Tj = 25C REGL1 REGL2 IBias IO = 5 mA to 1.5 A, Tj = 25C IO = 250 mA to 750 mA, Tj = 25C Tj = 25C
Bias current fluctuation to input IBias(IN) VI = 10.5 V to 25 V, Tj = 25C Bias current fluctuation to load Ripple rejection ratio * Design reference data IBias(L) IO = 5 mA to 1 A, Tj = 25C RR VI = 11.5 V to 21.5 V, IO = 100 mA, f = 120 Hz
Note) The characteristics listed below are theoretical values based on the IC design and are not guaranteed.
Parameter Output noise voltage
Symbol VNO
Conditions f = 10 Hz to 100 kHz
Min
Typ 52 2 700 2.0 - 0.5 150
Max
Unit V V mA A mV/C C
Minimum input/output voltage VDIF(min) IO = 1 A, Tj = 25C difference Output short-circuit current Peak output current Output voltage temperature coefficient Thermal protection operating temperature IO(Short) IO(Peak) VI = 35 V, Tj = 25C Tj = 25C
VO / Ta IO = 5 mA, Tj = 0C to 125C Tj(TH) IO = 5 mA
SFF00011BEB
5
AN78xxNSP Series
I Electrical Characteristics at Ta = 25C (continued)
* AN7809NSP (9 V type) The specified condition Tj = 25C means that the test should be carried out within so short a test time (within 10 ms) that the characteristic value drift due to the chip junction temperature rise can be ignored. Unless otherwise specified, VI = 15 V, IO = 500 mA, CI = 0.33 F and CO = 0.1 F Parameter Output voltage Output voltage tolerance Line regulation 1 Line regulation 2 Load regulation 1 Load regulation 2 Bias current Symbol VO1 VO2 Tj = 25C VI = 12 V to 24 V, IO = 5 mA to 1 A Tj = 25C, PD < 5 W Conditions Min 8.65 8.55 56 Typ 9 7 2 12 4.0 3.9 Max 9.35 9.45 180 90 180 90 8 1.0 0.5 Unit V V mV mV mV mV mA mA mA dB
REGIN1 VI = 11.5 V to 26 V, Tj = 25C REGIN2 VI = 12 V to 18 V, Tj = 25C REGL1 REGL2 IBias IO = 5 mA to 1.5 A, Tj = 25C IO = 250 mA to 750 mA, Tj = 25C Tj = 25C
Bias current fluctuation to input IBias(IN) VI = 11.5 V to 26 V, Tj = 25C Bias current fluctuation to load Ripple rejection ratio * Design reference data IBias(L) IO = 5 mA to 1 A, Tj = 25C RR VI = 11.5 V to 21.5 V, IO = 100 mA, f = 120 Hz
Note) The characteristics listed below are theoretical values based on the IC design and are not guaranteed.
Parameter Output noise voltage
Symbol VNO
Conditions f = 10 Hz to 100 kHz
Min
Typ 57 2 700 2.0 - 0.5 150
Max
Unit V V mA A mV/C C
Minimum input/output voltage VDIF(min) IO = 1 A, Tj = 25C difference output short-circuit current Peak output current Output voltage temperature coefficient Thermal protection operating temperature IO(Short) IO(Peak) VI = 35 V, Tj = 25C Tj = 25C
VO / Ta IO = 5 mA, Tj = 0C to 125C Tj(TH) IO = 5 mA
6
SFF00011BEB
AN78xxNSP Series
I Electrical Characteristics at Ta = 25C (continued)
* AN7810NSP (10 V type) The specified condition Tj = 25C means that the test should be carried out within so short a test time (within 10 ms) that the characteristic value drift due to the chip junction temperature rise can be ignored. Unless otherwise specified, VI = 16 V, IO = 500 mA, CI = 0.33 F and CO = 0.1 F Parameter Output voltage Output voltage tolerance Line regulation 1 Line regulation 2 Load regulation 1 Load regulation 2 Bias current Symbol VO1 VO2 Tj = 25C VI = 13 V to 25 V, IO = 5 mA to 1 A Tj = 25C, PD < 5 W Conditions Min 9.6 9.5 56 Typ 10 8 2.5 12 4.0 3.9 Max 10.4 10.5 200 100 200 100 8 1.0 0.5 Unit V V mV mV mV mV mA mA mA dB
REGIN1 VI = 12.5 V to 27 V, Tj = 25C REGIN2 VI = 13 V to 19 V, Tj = 25C REGL1 REGL2 IBias IO = 5 mA to 1.5 A, Tj = 25C IO = 250 mA to 750 mA, Tj = 25C Tj = 25C
Bias current fluctuation to input IBias(IN) VI = 12.5 V to 27 V, Tj = 25C Bias current fluctuation to load Ripple rejection ratio * Design reference data IBias(L) IO = 5 mA to 1 A, Tj = 25C RR VI = 13 V to 23 V, IO = 100 mA, f = 120 Hz
Note) The characteristics listed below are theoretical values based on the IC design and are not guaranteed.
Parameter Output noise voltage
Symbol VNO
Conditions f = 10 Hz to 100 kHz
Min
Typ 56 2 700 2.0 - 0.6 150
Max
Unit V V mA A mV/C C
Minimum input/output voltage VDIF(min) IO = 1 A, Tj = 25C difference Output short-circuit current Peak output current Output voltage temperature coefficient Thermal protection operating temperature IO(Short) IO(Peak) VI = 35 V, Tj = 25C Tj = 25C
VO / Ta IO = 5 mA, Tj = 0C to 125C Tj(TH) IO = 5 mA
SFF00011BEB
7
AN78xxNSP Series
I Electrical Characteristics at Ta = 25C (continued)
* AN7812NSP (12 V type) The specified condition Tj = 25C means that the test should be carried out within so short a test time (within 10 ms) that the characteristic value drift due to the chip junction temperature rise can be ignored. Unless otherwise specified, VI = 19 V, IO = 500 mA, CI = 0.33 F and CO = 0.1 F Parameter Output voltage Output voltage tolerance Line regulation 1 Line regulation 2 Load regulation 1 Load regulation 2 Bias current Symbol VO1 VO2 Tj = 25C VI = 15 V to 27 V, IO = 5 mA to 1 A Tj = 25C, PD < 5 W Conditions Min 11.5 11.4 55 Typ 12 10 2 12 4.0 4.0 Max 12.5 12.6 240 120 240 120 8 1.0 0.5 Unit V V mV mV mV mV mA mA mA dB
REGIN1 VI = 14.5 V to 30 V, Tj = 25C REGIN2 VI = 16 V to 22 V, Tj = 25C REGL1 REGL2 IBias IO = 5 mA to 1.5 A, Tj = 25C IO = 250 mA to 750 mA, Tj = 25C Tj = 25C
Bias current fluctuation to input IBias(IN) VI = 14.5 V to 30 V, Tj = 25C Bias current fluctuation to load Ripple rejection ratio * Design reference data IBias(L) IO = 5 mA to 1 A, Tj = 25C RR VI = 15 V to 25 V, IO = 100 mA, f = 120 Hz
Note) The characteristics listed below are theoretical values based on the IC design and are not guaranteed.
Parameter Output noise voltage
Symbol VNO
Conditions f = 10 Hz to 100 kHz
Min
Typ 75 2 700 2.0 - 0.8 150
Max
Unit V V mA A mV/C C
Minimum input/output voltage VDIF(min) IO = 1 A, Tj = 25C difference Output short-circuit current Peak output current Output voltage temperature coefficient Thermal protection operating temperature IO(Short) IO(Peak) VI = 35 V, Tj = 25C Tj = 25C
VO / Ta IO = 5 mA, Tj = 0C to 125C Tj(TH) IO = 5 mA
8
SFF00011BEB
AN78xxNSP Series
I Electrical Characteristics at Ta = 25C (continued)
* AN7815NSP (15 V type) The specified condition Tj = 25C means that the test should be carried out within so short a test time (within 10 ms) that the characteristic value drift due to the chip junction temperature rise can be ignored. Unless otherwise specified, VI = 23 V, IO = 500 mA, CI = 0.33 F and CO = 0.1 F Parameter Output voltage Output voltage tolerance Line regulation 1 Line regulation 2 Load regulation 1 Load regulation 2 Bias current Symbol VO1 VO2 Tj = 25C VI = 18 V to 30 V, IO = 5 mA to 1 A Tj = 25C, PD < 5 W Conditions Min 14.4 14.25 54 Typ 15 11 3 12 4.0 4.0 Max 15.6 15.75 300 150 300 150 8 1.0 0.5 Unit V V mV mV mV mV mA mA mA dB
REGIN1 VI = 17.5 V to 30 V, Tj = 25C REGIN2 VI = 20 V to 26 V, Tj = 25C REGL1 REGL2 IBias IO = 5 mA to 1.5 A, Tj = 25C IO = 250 mA to 750 mA, Tj = 25C Tj = 25C
Bias current fluctuation to input IBias(IN) VI = 17.5 V to 30 V, Tj = 25C Bias current fluctuation to load Ripple rejection ratio * Design reference data IBias(L) IO = 5 mA to 1 A, Tj = 25C RR VI = 18.5 V to 28.5 V, IO = 100 mA, f = 120 Hz
Note) The characteristics listed below are theoretical values based on the IC design and are not guaranteed.
Parameter Output noise voltage
Symbol VNO
Conditions f = 10 Hz to 100 kHz
Min
Typ 90 2 700 2.0 -1.0 150
Max
Unit V V mA A mV/C C
Minimum input/output voltage VDIF(min) IO = 1 A, Tj = 25C difference Output short-circuit current Peak output current Output voltage temperature coefficient Thermal protection operating temperature IO(Short) IO(Peak) VI = 35 V, Tj = 25C Tj = 25C
VO / Ta IO = 5 mA, Tj = 0C to 125C Tj(TH) IO = 5 mA
SFF00011BEB
9
AN78xxNSP Series
I Electrical Characteristics at Ta = 25C (continued)
* AN7818NSP (18 V type) The specified condition Tj = 25C means that the test should be carried out within so short a test time (within 10 ms) that the characteristic value drift due to the chip junction temperature rise can be ignored. Unless otherwise specified, VI = 27 V, IO = 500 mA, CI = 0.33 F and CO = 0.1 F Parameter Output voltage Output voltage tolerance Line regulation 1 Line regulation 2 Load regulation 1 Load regulation 2 Bias current Symbol VO1 VO2 Tj = 25C VI = 21 V to 33 V, IO = 5 mA to 1 A Tj = 25C, PD < 5 W Conditions Min 17.3 17.1 53 Typ 18 14 4 14 4.0 4.1 Max 18.7 18.9 360 180 360 180 8 1.0 0.5 Unit V V mV mV mV mV mA mA mA dB
REGIN1 VI = 21 V to 33 V, Tj = 25C REGIN2 VI = 24 V to 30 V, Tj = 25C REGL1 REGL2 IBias IO = 5 mA to 1.5 A, Tj = 25C IO = 250 mA to 750 mA, Tj = 25C Tj = 25C
Bias current fluctuation to input IBias(IN) VI = 21 V to 33 V, Tj = 25C Bias current fluctuation to load Ripple rejection ratio * Design reference data IBias(L) IO = 5 mA to 1 A, Tj = 25C RR VI = 22 V to 32 V, IO = 100 mA, f = 120 Hz
Note) The characteristics listed below are theoretical values based on the IC design and are not guaranteed.
Parameter Output noise voltage
Symbol VNO
Conditions f = 10 Hz to 100 kHz
Min
Typ 110 2 700 2.0 -1.1 150
Max
Unit V V mA A mV/C C
Minimum input/output voltage VDIF(min) IO = 1 A, Tj = 25C difference Output short-circuit current Peak output current Output voltage temperature coefficient Thermal protection operating temperature IO(Short) IO(Peak) VI = 35 V, Tj = 25C Tj = 25C
VO / Ta IO = 5 mA, Tj = 0C to 125C Tj(TH) IO = 5 mA
10
SFF00011BEB
AN78xxNSP Series
I Application Notes
1. PD Ta curves of SP-3SU
6.00 Mounted on Al board (50 x 50 x t2.0 mm3) Rth(j-a) = 25.0C/W
PD T a
5.00
Power dissipation PD (W)
4.00
Mounted on glass epoxy board 2 (50 x 50 x t1.5 mm3) Rth(j-a) = 89.3C/W Mounted on glass epoxy board 1 (20 x 20 x t1.7 mm3) Rth(j-a) = 147.0C/W
3.00
2.00 1.40 1.00 0.85 0.70 0 0
Independent IC without a heat sink Rth( j-a) = 178.0C/W 25 50 75 100 125 150
2. Main Characteristics Minimum input/output voltage difference vs. load current characteristic
2 Tj = 25C 1.8 1.6 1.4
Ambient temperature Ta (C)
Minimum input/output voltage difference temperature characteristic
2.000 IO = -1 A 1.980 1.960 1.940
VDIF (V)
1.2 1.0 0.8 0.6 0.4 0.2 0 0 0.2 0.4 0.6 0.8 1
VDIF(min) (V)
1.920 1.900 1.880 1.860 1.840 1.820 1.800 -40 -20
0
20
40
60
80
100
120
IO (A)
Ta (C)
Peak output current temperature characteristic
2.500
6
Current limit characteristics
Tj = 25C
2.000
5
4
IO(Peak) (A)
1.500
VO (V)
VI = 30 V 3 VI = 20 V VI = 10 V 2
1.000
0.500
1
0.000 -40
-20
0
0
20
40
60
80
100
120
0
0.5
1
1.5
2
Ta (C)
SFF00011BEB
IO (A)
11
AN78xxNSP Series
I New Package Dimensions (Unit: mm)
* SP-3SUA (Lead-free package) 6.500.10 5.400.10 (4.35) (3.00)
(1.80) (2.50)
(0.50)
5.500.10
(5.30) 9.800.20
2.500.20
(0.50)
2
1.000.20 3 0.75+0.10 -0.05
1
2.30 4.600.10
0.23 M
0.100.10 0.50+0.10 -0.05
12
SFF00011BEB
2.300.10
1.000.20
Request for your special attention and precautions in using the technical information and semiconductors described in this material
(1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technologies described in this material and controlled under the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. (2) The technical information described in this material is limited to showing representative characteristics and applied circuit examples of the products. It does not constitute the warranting of industrial property, the granting of relative rights, or the granting of any license. (3) The products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: * Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. * Any applications other than the standard applications intended. (4) The products and product specifications described in this material are subject to change without notice for reasons of modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (5) When designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage and heat radiation characteristics. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, redundant design is recommended, so that such equipment may not violate relevant laws or regulations because of the function of our products. (6) When using products for which dry packing is required, observe the conditions (including shelf life and after-unpacking standby time) agreed upon when specification sheets are individually exchanged. (7) No part of this material may be reprinted or reproduced by any means without written permission from our company.
Please read the following notes before using the datasheets
A. These materials are intended as a reference to assist customers with the selection of Panasonic semiconductor products best suited to their applications. Due to modification or other reasons, any information contained in this material, such as available product types, technical data, and so on, is subject to change without notice. Customers are advised to contact our semiconductor sales office and obtain the latest information before starting precise technical research and/or purchasing activities. B. Panasonic is endeavoring to continually improve the quality and reliability of these materials but there is always the possibility that further rectifications will be required in the future. Therefore, Panasonic will not assume any liability for any damages arising from any errors etc. that may appear in this material. C. These materials are solely intended for a customer's individual use. Therefore, without the prior written approval of Panasonic, any other use such as reproducing, selling, or distributing this material to a third party, via the Internet or in any other way, is prohibited.
2001 MAR

▲Up To Search▲

Price & Availability of AN7810NSP

	To Download AN7810NSP Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .